How the software check for serviceability of the structure according to the technical standards in APF WoodBeam and APF WoodTruss.
Serviceability means the structure must appear safe and comfortable to the people who use it, excessive floor deflection could worry the people in a building. APF WoodTruss and APF WoodBeam perform serviceability checks in accordance with Eurocodice 5 (EN 1995-1-1:2004 + A1:2008 + A2:2014).
In Eurocode 5 the deflection of a member is required at two stages:
Immediately when action are applied.
After time-dependent deformation has taken place.
Instantaneous and creep deformations are related by the deformation factor kdef :
ucreep = kdef uinst
The final deflection ufin may be obtained by superimposing the creep deformations ucreep on the instantaneous deformation uinst
The deformation factor kdef also appears in the relationships between the mean and final mean value of the modulus of elasticity (and shear modulus, and slip modulus) for example:
Emean,fin = Emean / (1 + kdef)
If the distribution of member forces and moments is affected by the stiffness distribution in the structure, for example when the structure is composed by different materials or materials with different time-dependent properties, the internal actions have to be derived using the final mean value dof the modulus of elasticity, for example:
Emean,fin = Emean / (1 + ψ2 kdef)
On the other hand, if this does not happen, when the stiffness distribution within the structure does not affect the distribution of internal stress resultants, for example where all material being used have the same time-dependent properties, the internal actions have to be derived using the mean value of the modulus of elasticity Emean
For second-order linear elastic analyses, design values of the modulus of elasticity (not adjusted for duration of load) must be used, for example:
Ed = Emean / γM
At the instantaneousconditions, Eurocode 5 uses the characteristic load combination to derive the deformation of members. In this short-term situation, the creep behaviour of the member is not relevant (it has not yet had any effect on the structure), deformations have to be derived using the mean value of the modulus of elasticity Emean
At the final conditions, Eurocode 5 uses the quasi-permanent load combination to derive the deformation of members. The final deflection ufin should be obtained by superimposing the creep deformations ucreep on the instantaneous deformation uinst
For structures consisting of members, components and connections with the same creep behaviour, the total deflection will be the superimposition of the creep deformation calculated with the quasi-permanent combination on the instanteneouns deformation calculated for the characteristic combination of actions, where the final deformation can then be written as:
ufin = ucreep + uinst = uinst (1 + kdef)
If he structure consists of members having different creep behaviour, the creep deformation should be calculated using the quasi-permanent combination of actions with the final mean value of the modulus of elasticity, and the final deflection is obtained adding the instantaneous deformation due to the difference between the characteristic and the quasi-permanent combination of actions (calculated using the mean value of the modulus of elasticity).
In APF WoodBeam and APF WoodTruss, the settings dialog window contains the following options : Combine Actions and Same Creep Behaviour
In APF WoodBeam and in APF WoodTruss, the internal actions and deformations are evaluated with two models:
Elements are modelled with
mean values
of the appropriate modulus of elasticity.
Elements are modelled with
final mean values
of the appropriate modulus of elasticity.
At the same time, the effects of actions are stored for both:
If Combine Actions is enabled, the effects of actions for each design situation are obtained by first combining forces on members and then computing their overall effect, otherwise the effects are calculated for each load group first and then they are combined to give the design situation value.
In the first case the actions are combined, in the second their effects.
Using the mean or using the final mean values of the modulus of elasticity, shear modulus and slip modulus.
The Same Creep Behaviour option discriminates between the use of the effects calculated with the mean values or the final mean values of the elastic material properties.
At ULS the effects of actions are multiplied by partial factors to obtain the design value, and verification is undertaken to demonstrate that they are less than or equal to the design resistances.
The effects of actions used for the verification are those calculated with the mean or final mean elastic modulus depending on the value of the Same Creep Behaviour option.
At SLS, for instantaneous conditions, deflection is always evaluated using the mean value of the modulus of elasticity.
At SLS, for final conditions:
ufin,G = uinst,G (1 + kdef)
and
ufin,Q,1 = uinst,Q,1 (1 + ψ2 kdef)
and
ufin,Q,i = uinst,Q,i (ψ0 + ψ2 kdef)
In APF WoodBeam and in APF WoodTruss, the verification is carried out for:
The programs normally perform all these verifications, but it is possible to leave only one of them active, or to specify different limits for each one.